Spiral Groove Bearing Geometry Variation Effect on Left Ventricular Assist Device Impeller Performance

Authors

  • Shirly Empaling School of Biomedical Engineering and Health Sciences, Faculty of Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor, Malaysia
  • Ahmad Zahran Md Khudzari IJN-UTM Cardiovascular Engineering Centre, Institute of Human Centered Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor, Malaysia
  • Muhammad Rashidi Abdul Kadir School of Biomedical Engineering and Health Sciences, Faculty of Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor, Malaysia
  • Kahar Osman IJN-UTM Cardiovascular Engineering Centre, Institute of Human Centered Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor, Malaysia
  • Akmal Hakim Mohamad Hudzari School of Biomedical Engineering and Health Sciences, Faculty of Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor, Malaysia
  • Mohammad Hasbullah Padzillah School of Mechanical Engineering, Faculty of Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor, Malaysia
  • Ishkrizat Abdul Talib Faculty of Mechanical and Manufacturing, Universiti Tun Hussein Onn Malaysia, Parit Raja, Johor, Malaysia
  • Mohamed Ezani Abdul Taib Institut Jantung Negara, 50400, Kuala Lumpur, Malaysia
  • Aizai Azan Abdul Rahim Institut Jantung Negara, 50400, Kuala Lumpur, Malaysia

Keywords:

mechanical heart assist device, spiral groove bearing, haemolysis, impeller design

Abstract

Mechanical heart assist device has been accepted as a reliable treatment modality for advanced heart failure patient option other than orthotropic heart transplantation. One type of the device is a centrifugal rotary mechanical blood pump that has an impeller levitated using a magnetic motor system in which, it reduces blood damage compared to its predecessors. Spiral Groove Bearing (SGB) is proposed as another design consideration to further decrease blood damage, increasing blood flow in the tight gaps, while maintaining pump performances. There were few studies investigating several aspects of SGB effect on blood flow within the mechanical blood pump, however no study has been done on the SGB geometry configurations, and its effect on device performance. In this study, two design factors of SGB geometry were simulated using computational fluid dynamics (CFD) software – a gap between impeller and housing, and SGB groove depths. The resulting variants were then evaluated using several performance indexes which are pump pressure output, average washout flow, hemolysis index, bearing load carrying capacity and pump efficiency. From the results, there are two conclusions that can be drawn. By deepening SGB groove depth, blood pump performance increased, while increasing the gap between the impeller and pump housing, most performance indexes were reduced. Scoring and screening method was also utilized to evaluate the best variant and it was found that, the variant with SGB groove depths 1000 ?m and gap of 80 ?m was the best in term of overall performances.

Downloads

Published

2021-01-16

How to Cite

Empaling, S. ., Md Khudzari, . A. Z. ., Abdul Kadir, M. R. ., Osman, K. ., Mohamad Hudzari, A. H. ., Padzillah, M. H. ., Abdul Talib, . I., Abdul Taib, M. E. ., & Abdul Rahim, A. A. (2021). Spiral Groove Bearing Geometry Variation Effect on Left Ventricular Assist Device Impeller Performance. CFD Letters, 11(1), 86–101. Retrieved from https://akademiabaru.com/submit/index.php/cfdl/article/view/3112
صندلی اداری سرور مجازی ایران Decentralized Exchange

Issue

Section

Articles

Most read articles by the same author(s)

فروشگاه اینترنتی